Protect your engine from harmful contaminants and ensure smooth performance with the ‌15600-41010 Oil Filter‌, a direct OEM replacement for ‌AY10-0T-Y022‌. Engineered by ‌VK‌ to meet exacting factory standards, this high-quality oil filter delivers superior filtration efficiency, robust construction, and seamless compatibility with Toyota, Lexus, and select Asian vehicles. Avoid aftermarket inconsistencies and safeguard critical engine components with a filter built for reliability and precision.

Key Features of the 15600-41010 Oil Filter‌

Multi-Layer Synthetic Filtration Media‌

Captures ‌98% of particles‌ as small as ‌25 microns‌, including dirt, metal shavings, and carbon sludge.
High-capacity design resists clogging, maintaining optimal oil flow even in extreme temperatures (-40°F to 392°F).

Anti-Drainback & Pressure Relief Valves‌

Silicone Anti-Drainback Valve‌: Keeps oil in the filter during shutdown to prevent dry starts.
Bypass Valve‌: Opens at ‌12–15 psi‌ to ensure continuous oil flow if the media becomes blocked.

Heavy-Duty Construction‌

Steel Housing‌: Reinforced casing withstands up to ‌450 psi burst pressure‌ for high-performance engines.
Viton® Gasket‌: Resists heat, oil additives, and swelling for a leak-free seal.

OEM Fitment & Compatibility‌

Direct replacement for ‌AY10-0T-Y022‌ and OEM part ‌15600-41010‌.
Fits:
Toyota‌: Camry (2018–2024), RAV4 (2019–2024), Tacoma (2020–2024), 4Runner (2021–2024).
Lexus‌: NX 300 (2018–2024), RX 450h (2020–2024).
Engines‌: 2.5L A25A-FKS, 3.5L 2GR-FKS, 2.4L Turbo T24A-FTS.
Symptoms of a Bad Oil Filter‌

Replace your oil filter immediately if you experience:

Illuminated Oil Pressure Light‌: Restricted oil flow due to clogged media.
Engine Overheating‌: Reduced lubrication from degraded oil viscosity.
Exhaust Smoke‌: Burning sludge caused by poor filtration.
Loud Valve Noise‌: Insufficient oil reaching the top end of the engine.
Installation Guide‌
Drain Old Oil‌:
Run the engine for 3–5 minutes to warm the oil, then drain via the plug (14mm socket).
Remove Old Filter‌:
Use a ‌65mm oil filter wrench‌ to loosen the filter. Clean the mounting surface thoroughly.
Prepare New Filter‌:
Lubricate the Viton® gasket with fresh oil to prevent sticking.
Install 15600-41010 Filter‌:
Hand-tighten until snug, then add a ‌½ turn‌ (do not overtighten).
Refill Oil‌:
Use manufacturer-recommended oil (e.g., 0W-20 synthetic) and check for leaks.

Tip: Replace the filter every ‌5,000–10,000 miles‌ or per your vehicle’s maintenance schedule.

Why Choose VK OEM 15600-41010 Over Generic Filters?‌
Exact OE Specifications‌: Matches factory dimensions and flow rates for flawless integration.
Extended Engine Life‌: Reduces wear on turbochargers, bearings, and timing chains.
Cost Savings‌: Priced 25% lower than dealership parts with identical performance.
Warranty Assurance‌: Backed by a ‌24-month unlimited-mileage warranty‌.

Avoid Knockoffs: Cheap filters often use paper media that disintegrates, risking engine failure.

Conclusion‌
The ‌15600-41010 Oil Filter‌ (replacing ‌AY10-0T-Y022‌) is a vital investment in maintaining your vehicle’s engine health and performance. By choosing VK’s OEM-certified filter, you ensure optimal contamination control, pressure stability, and long-term reliability. Pair it with high-quality synthetic oil for maximum protection and fuel efficiency. Always verify fitment using your VIN and trust OEM engineering for peace of mind.

Keywords‌: 15600-41010 Oil Filter, AY10-0T-Y022 Replacement, VK OEM Oil Filter, Toyota Camry Oil Change, Lexus NX 300 Filter, Tacoma 2.4L Turbo Oil Maintenance.

SEO-optimized for car enthusiasts, mechanics, and auto parts retailers. For bulk orders or technical support, contact certified VK distributors.